Wall Ties

All of our products are available with or without retaining discs and in custom sizes. All wall ties comply with IS EN845 1-3:2013 (+A1: 2016).

New! Long wall ties for extra wide cavities. Read more

Guidelines for Usage

The correct type and density of wall ties is controlled by the area of unsupported brickwork, the exposure to wind, the cavity size and the nature of the structure. Detailed recommendations can be found in the following pubhlications:- IS EN845, PD6697 - Specification for metal ties for cavity wall construction B.S. 5628 Parts 1 and 2 - Use of Masonry
CPQ Chapter V - Wind Loads

General Guide to Density for Cavities up to 150mm

Cavity Width less than 50mm One leaf 75mm-90mm thick. Not less than 4.9 ties /m2.
Cavity Width 50-75mm Both leaves more than 90mm thick. Not less than 2.5 ties /m2.
Cavity width 76-100mm Both leaves more than 90mm thick. Not less than 3 ties /m2.
Cavity width 101-150mm Both leaves more than 90mm thick. Not less than 4.9 ties /m2.

Catalogue of Wall ties

Safer Ties

Show Specification

Safer Ties

Material Specification

Austenitic stainless steel strip to EN10088 as required by EN845 1-3.

Performance Specification

17 x 2.5mm Test Required
Tensile Strength 15.19KN 0.94KN
Compressive Strength 2.71KN 1.075KN
Anchorage Strength 6.25KN 2.02KN

Cyclic Movement

The tensile strength retained after being subjected to cyclic movement was in no case less than 75% of the characteristic tie tensile strength.

Based on a density of 3 ties per m2. Standards IS268 and EN845 1-3.

Cert NO. 012297 (098115) R6/06886A

wall ties S/P-(C) Flat Safety Tie
wall ties S/C-(C) Crimped Safety Tie
wall ties S/T-(C) Vertical Twist Safety Tie
wall ties Channel Anchor
wall ties RAT-(C)
wall ties DAT-(C) Dovetail-Safety Anchors
wall ties DAT-(C) Dovetail-Safety Anchors
wall ties S/T/D-(C) Debonding safety tie, with durable plastic sheath

Vertical Twist Ties with Insulation Retaining Pin

Show Specification

S/T-HS Vertical Twist Tie with Insulation Retaining Pin

Material Specification

Austenitic stainless steel strip to EN10088 as required by EN845-1-3.

Performance Specification

17 x 2.5mm Test IS268 Required
Tensile Strength 21.00KN 0.94KN
Compressive Strength 2.65KN 1.075KN
Anchorage Strength 3.39KN 2.42KN

Cyclic Movement

The tensile strength retained after being subjected to cyclic movement was in no case less than 75% of the characteristic tie tensile strength.

Based on a density of 3 ties per m2.

Cert NO. R6/4583G

wall ties S/T-HS Vertical Twist Tie with Insulating Retaining Pin

Wire Ties

Show Specification

Wire Tie Specifications

S/W Double Triangle Wire Tie

Features an attached Plastic Insulation Retainer.

Material Specification

Austenitic stainless steel strip to EN10088 as required by EN845 1-3.

Performance Specification

Test Required
Tensile Strength 2.289KN 0.94KN
Compressive Strength 1.205KN 1.075KN
Anchorage Strength 2.02KN 2.02KN

Based on a density of 3 ties, per m2.

Cert NO. BRE 234-521

wall ties S/W- Double Triangle Wire Tie
wall ties Double Triangle Tie S/W
wall ties Continuous Wire Wall Tie
wall ties S/W/- + Disc and Double Triangle Wire Tie.

Accessories

wall ties Insulation Retaining Disc